Materials

Smart Lock Materials and Finishes

Compare smart lock materials and finishes across our range, then narrow them by door and installation site. Compare the housing material and available finishes for each model: the housing is SUS304 stainless steel on most models and iron on a few lower-cost ones, and finishes range from brushed stainless to Athens black or red bronze. The six guides below go deeper.

Smart locks in brushed stainless steel, black and red bronze finishes
Quick Check

Choose by Where the Lock Goes

Where will the lock be fitted?

Indoor Rooms and Offices

Bedrooms, offices and rental rooms keep the lock out of the weather, so the choice comes down to door fit, look and budget.

  • Material:SUS304; the iron versions of Z1 and M2 suit lower-cost projects
  • Protection:The indoor models are rated IP55 and intended for indoor doors
  • Finish:Match the hinges, handles and trim nearby, and approve it on a sample under the room's lighting
  • Models:F2, Z1, M2

Covered Entrances

Corridors, porches and lobbies see daily use and cleaning. A roof helps, but check whether wind-driven rain, splash or cleaning water still reaches the lock.

  • Material:SUS304 housing components; iron G1 and G3 for lower-cost apartment projects
  • Protection:Most apartment and face recognition models are IP55, intended for indoor and covered doors; if water can reach the lock, compare the IP66 models
  • Finish:Pick one that stands up to frequent touching and the building's cleaning products, and agree the cleaning method at handover
  • Models:G2, G11, R1

Exposed Doors and Gates

Doors and gates without cover take rain, splash and sun directly on the lock, so start from a model rated for water entry.

  • Material:SUS304 housing components
  • Protection:Choose from the IP66 models; IP66 covers water getting into the housing, not corrosion or wear of the finish
  • Finish:Judge it in daylight on site, and plan how dust and water marks will be cleaned off
  • Models:A2, A11, L1

Coastal Sites

Near the sea, treat it as two questions: salt exposure decides the material and finish, and rain exposure decides the protection rating.

  • Material:SUS304 after a site assessment: salt exposure, sheltered surfaces where salt collects, and how often the locks can be cleaned
  • Protection:An IP66 model if rain reaches the lock; under cover, compare the actual exposure with the model's rating
  • Finish:Smooth, even surfaces hold less salt and show less staining; plan regular wiping and drying, including the strike and screw heads
  • Models:Chosen after the site check; IP66 models such as A2 and L1 are the usual starting point. For L1, specify the rear-body material, iron or stainless steel, with the proposed configuration
Guides

Material Guides

By Model

Housing Material by Model

HousingModels
SUS304 stainless steel housing componentsA1, A11, A6, R9, A2, A2 Double-Sided, A11 Double-Sided, A6 Double-Sided, R9 Double-Sided, R1, R2, R8, G2, G11, F2, M1; J Series hardware
SUS304 and aluminum alloyA7 glass door lock
SUS304 front housing; rear body in iron or stainless steelL1 rim gate lock
SUS304 in stainless steel; iron in blackZ1, M2
Iron, for lower-cost projectsG1, G3
SUS304 panels and handlesRA Series mechanical locks

Materials vary by model and component. The table covers the housing only; lock bodies, internal mechanisms and fasteners are specified separately. Each model page lists its housing and finishes.

FAQ

Frequently Asked Questions

Are all SivoLock locks stainless steel?

No. Most models use SUS304 housing components, but G1 and G3 have iron housings, and Z1, M2 and the L1 rear body have iron versions. The table above lists each model.

Can a black or bronze lock have a stainless steel housing?

Yes. A black A2 is SUS304 with an Athens black finish, while a black Z1 or M2 is iron. Finish options lists the material under each color, model by model.

Which material should I choose for a coastal site?

Treat it as two questions. Salt exposure decides the material and finish, so assess the site and the cleaning plan first; rain and splash decide the protection rating, and for exposed doors we recommend the IP66 models. See corrosion resistance.

Can you match a custom color?

Custom colors can be reviewed for project orders. See colors and finish options.

Get Started

Ask About Materials and Finishes

Tell us where the locks will be fitted, the finish you have in mind and the quantity. We will suggest models with the right housing and finish.