Smart Lock Surface Finishing
Approve a finish by knowing how it was made and what to look for on the panel. Smart lock surface finishing decides how the lock looks on the door and how that look holds up to touching, cleaning and weather. Our Jinhua factory brushes, polishes and cleans the stainless steel parts in house; selected finishes are applied by specialist partners.

What We Do In House
Our Jinhua factory has three polishing lines and an automated cleaning line for stainless steel parts. Polishing sets the grain or shine of the surface, and cleaning removes polishing residue before the part moves on to assembly or to its finish. Selected treatments, including PVD coating and electroplating, are applied by specialist finishing partners; we set the finish specification and check appearance and consistency in final inspection. The factory page shows the lines.
Finishing Processes Compared
Which finish are you considering?
Brushed Stainless
Abrasive belts or pads give the steel fine, straight lines. In stainless steel standards this is the No. 4 finish (EN 10088-2 2J or 2K).
- Look:Satin, directional grain; light reflects along the lines
- Layer:None; the surface is the steel itself, so scratches show steel underneath
- Care:Wipe along the grain
- Check:Grain runs the same way on front and rear panels and on the handle
Mirror Polished
Progressively finer polishing gives a bright, non-directional surface: the No. 8 finish (EN 10088-2 2P).
- Look:Highly reflective; shows the room around it
- Layer:None; the surface is the steel itself
- Care:Fingerprints and fine scratches show more than on brushed steel
- Check:No polishing marks or haze at edges and around openings
PVD Coating
Physical vapor deposition builds a very thin metal-compound film on the part inside a vacuum chamber. The thickness depends on the coating system; decorative films are thin enough to follow the texture beneath them.
- Look:Metallic colors such as gold, bronze, gray and black, depending on the compound used
- Layer:The film copies the surface under it: brushed under PVD stays brushed, polished stays bright
- Care:Mild cleaner and a soft cloth; no abrasive pads
- Check:Even color across all parts, under daylight and indoor light
Electroplating
Metal layers are deposited on the part in a plating bath, for example chromium over nickel and copper layers.
- Look:Bright or satin metal colors
- Layer:Plating builds up more on outer edges and projecting corners, and less in deep recesses and holes
- Care:Follow the care sheet for the plated finish
- Check:Coverage and evenness on edges, recesses and openings as well as the flat face; for a specified thickness, ask where it is measured
Powder Coating and Paint
A colored powder or paint is applied and cured. Architectural powder coating standards such as Qualicoat set minimum film thicknesses of about 50–60 µm.
- Look:Solid colors in matt, satin or gloss; almost any color
- Layer:Much thicker than PVD or plating, so it hides fine surface texture
- Care:Mild cleaner; avoid solvents and abrasive pads
- Check:Even coverage at edges, gloss level, and how a color matches the other hardware
The finish names on our model pages (Athens black, red bronze, starry gray, titanium gold, black bronze) describe the appearance. If your project requires a particular process, such as PVD, state it in the inquiry and we will confirm whether the model can be supplied that way.
How to Check a Finished Panel
| Look at | What to check | What to keep for repeat orders |
|---|---|---|
| Broad faces | Even color, texture and gloss; no marks or haze | The approved sample and finish name |
| Edges, corners, openings | Coverage and appearance match the flat face | Photos of the approved sample's edges |
| Handle and rear panel | Grain direction and color match the front | The model and version with the finish |
| Logo or marking | Position, contrast and sharpness on the finish | Approved artwork and the marked sample |
| Next to the door hardware | Gloss and tone beside hinges, handles and trim | Notes on lighting used for approval |
View the sample in daylight and under the lighting where it will be installed, holding it at the same angle each time. Adhesion and salt spray tests are explained on corrosion resistance, and our guide to reading salt spray test hours shows when two reports can be compared.
Care After Installation
Protect fitted locks during building work and clean them before handover. Use a soft cloth and a mild cleaner, wipe brushed steel along the grain, and keep liquid away from the reader and joints. Abrasive pads damage every finish on this page. The full cleaning steps are on corrosion resistance.
Frequently Asked Questions
Does a gold or bronze color mean the finish is PVD?
Not necessarily. Similar colors can come from PVD, plating or coating. If a particular process matters, specify it, and we will confirm what the model can offer.
Which finishes do you apply in house?
Brushing, polishing and cleaning of stainless steel parts, and routine finishing, are done in our Jinhua factory. PVD coating and electroplating are done by specialist partners, under our finish specification and final inspection.
Is brushed stainless the same on every product?
No. Grain, texture and reflection vary by part and process. Approve the actual model's sample, especially when it has to match other hardware.
How thick is a PVD coating?
It depends on the coating system. Decorative PVD films are far thinner than a powder coating, which standards such as Qualicoat set at 50–60 µm or more, so the brushed or polished texture underneath still shows.
Can you match our own finish or color?
Custom finishes can be reviewed for project orders with a physical sample or RAL reference. See colors and finish options and OEM/ODM.
Send Your Finish Reference
Send a photo of the door and its hardware, the finish you want, any process requirement and the quantity. We will suggest the model and finish, and prepare a sample.