Project Doors

Smart Locks for Door Manufacturers and Projects

Smart locks for door manufacturers and building projects are chosen per door group, not per building: profile doors, glass doors, room doors and gates each need a different lock format, and every group needs its own lock body, kit and sample before production. We turn your door schedule into approved door groups, then into packed, labeled supply.

Smart locks being fitted to aluminum profile doors in a door factory
Door Schedule

Group the Doors First

Sort the schedule by what decides the hardware:

  1. Construction: aluminum profile, glass, wood, steel or gate.
  2. Thickness and frame: door thickness, stile or frame width, glass thickness.
  3. Preparation: an existing lock body or cutout, or a new drawing.
  4. Opening: handing, opening direction and how the door closes.
  5. Use: who opens it, from which side, and whether it is exposed to weather.

Doors that match on all five form one group, with one model and one kit approved on a sample door. Our door schedule guide shows a worked layout.

Formats

Match Each Door Group to a Lock

Door groupLock formatStart withWhat we need
Aluminum or thermal-break profile doorsNarrow-panel lever or automaticA1, A11, A6, R9Stile width, space inside the profile, mortise, handle clearance
Frameless or framed glass doorsGlass door lock with clamp or drilled mountingA7Glass or frame thickness, gap, receiving side, any existing holes
Wooden room and office doorsIndoor lever or rosetteF2, Z1Door thickness, latch or 4585 mortise, handle clearance
American-format doorsSmart deadbolt or smart leverM1, M2Bore, backset, edge preparation, existing handle
Entrance and security doorsWide-panel entrance lockA2, apartment locksMortise, panel area, exposure
Gates and service doors without a pocketSurface-mounted rim lockL1Rear-body support, strike position, gap to the post
Doors that need no electronicsMechanical panel and handleRA SeriesRA code, lock body, cylinder, strike

Each model page lists its specifications, versions and lock bodies. Lock bodies and strikes can also be supplied on their own; see accessories and mortises.

Door Factories

Integrating Locks Into a Door Range

For a door manufacturer, the lock is part of the door's design. Send the door drawing before the design is released, so the mortise pocket, spindle hole, cable or fixing holes and strike are prepared to the lock's drawing. Decide early where the lock is fitted:

Fitted atPackingCheck
The door factoryLocks packed by door type for the production lineFit on the line, then a function check before the door ships
On siteKits packed and labeled by door group and floorInstallers fit to the drawing; the first door is checked against the sample
SplitLock body fitted in the factory, panels on siteBoth stages share one labeled reference

Our door factory integration guide and mortise coordination guide cover these steps in detail.

Process

From Sample Door to Batch

  1. Door-group review: schedule, drawings or photos, quantities and access needs.
  2. Proposal: a model, version, lock body and kit for each group, with a sample plan.
  3. Sample door: fit the sample on a real or representative door, following the installation guide. With the door open, check fit, handle, credentials and the backup key; then close it and check that the bolt meets the strike.
  4. Approval: record the model, version, finish, lock body, kit, artwork and packing for each group.
  5. Pilot run (where needed): first units are compared with the approved sample before regular production.
  6. Supply: each carton carries the door group and model, so the right kit reaches the right door.
  7. Repeat orders: any change to parts, finish or packing is confirmed in writing first.
Quality

Quality and Inspection

Every complete lock is checked for its functions, appearance and accessories before packing, and packed batches are sampled for labels, quantities and versions. If your project needs third-party inspection or specific documents, tell us before the order is confirmed. See quality and testing and the pre-shipment inspection checklist.

Supply

Finish, Branding and Spares

A project can use several finishes, as long as each door group has its own reference. Approve the finish on the sample door next to the other hardware. Logo, manuals and packaging are covered on OEM/ODM. Order spare locks and parts by door group, so a replacement matches the door it goes on; our spare-parts planning guide helps size them.

FAQ

Frequently Asked Questions

Can you review our door drawings?

Yes. Send the drawings or photos and the door groups. We match the model, lock body and kit to each group before the sample.

Can one project mix smart and mechanical locks?

Yes. Keep them as separate door groups: RA Series for mechanical doors, and the chosen smart lock for the rest.

Can glass doors use the same preparation as profile doors?

No. A7 mounts with a clamp or by drilling the frame, which is a different preparation from the mortise of a profile door lock.

Do you supply lock bodies separately?

Yes. Mortises, strikes and fixing kits are supplied with the locks or on their own for door production and replacements.

How do installers know which lock goes on which door?

Each carton is labeled with the door group and model from the approved schedule.

Get Started

Send Your Door Schedule

Send the door schedule or photos, the door types, quantities and where the locks will be fitted. We will propose a lock and kit for each door group and a sample plan.