L1 IP66 Rim Gate Smart Lock
The L1 IP66 rim gate smart lock mounts its lock body on the rear face of the gate, so it fits metal gates and project doors 35–65 mm thick that have no pocket for a mortise. It runs on 4 AA batteries, and comes in a TTLock or a Tuya Wi-Fi version. L2 is the L1 version with a keypad built into the rear lock body, for PIN operation from the inside.

L1 Specifications
- Format
- Surface-mounted rim gate lock
- Housing
- SUS304 front housing; rear body in iron or stainless steel
- Finishes
- Stainless steel; black
- Door thickness
- 35–65 mm
- Front panel
- 155 × 60 mm, 15.8 mm deep
- Rear body
- 130 × 100 mm, projects about 45 mm
- Strike
- About 35 mm wide
- Protection
- IP66
- Power
- 4 × AA batteries
- Emergency power
- 5 V Type-C
- Access
- Fingerprint, PIN, RFID card, mechanical key
- Versions
- TTLock Bluetooth; Tuya Wi-Fi
- Working temperature
- −30°C to 70°C
- Options
- L2 version with a keypad on the rear body (PIN operation from the inside); remote control
Why a Rim Body
A mortise lock sits inside the door; L1's body sits on the rear face of the gate and stays visible. That suits gates and metal doors without a mortise pocket, as long as the rear face has firm support at the fixing points. Check room for the 45 mm projection and the 35 mm strike, the gap between gate and post, and how the gate swings on its hinges. On paired gates, hold the passive leaf firmly. See our installation guide.
Versions and L2
| Version | Fingerprints | PINs and cards |
|---|---|---|
| TTLock (Bluetooth) | 100 | 250 PINs; 1,000 cards |
| Tuya (Wi-Fi) | 100 | Up to 300 in total |
Remote access on the TTLock version needs a TTLock gateway and a Wi-Fi connection; the Tuya version connects over the site's Wi-Fi. L2 is the L1 version with a keypad built into the rear lock body, for PIN operation from the inside. The front unit, gate fit and power stay the same as L1; decide who will use the inside keypad before you order. A remote control is available as an accessory. See app, gateway and access management.
Power and Location
L1 runs on 4 replaceable AA batteries, changed at the rear body. If they run flat, a power bank on the 5 V Type-C port powers the lock temporarily, and the mechanical key is a second backup.
L1 is rated IP66: dust-tight and protected against powerful water jets. It works from −30°C to 70°C, and we recommend it for exposed gates when it is fitted as the installation instructions describe. The front unit's circuit board is potted in compound inside its stainless steel housing; see how the electronics are sealed. The rear body comes in stainless steel or iron; iron suits lower-cost projects. For coastal sites, see corrosion resistance.
Compare Gate and Entrance Models
| Model | Mounting | Door thickness | Protection | Power |
|---|---|---|---|---|
| L1 (this model) | Surface-mounted rim body | 35–65 mm | IP66 | 4 × AA |
| A2 IP66 waterproof lock | Mortise in the door | 40–120 mm | IP66 | 4 × AA |
| A2 Double-Sided | 6068 motorized mortise | 40–120 mm | IP66 | 5,000 mAh lithium |
| A11 IP66 profile door lock | Profile mortise | 40–90 mm | IP66 | 1,000 mAh lithium or 4 × AAA |
Samples and OEM
Samples are available for evaluation; we confirm the version, door fit and accessories before an order. Fit the L1 sample on the actual gate. Check that the rear body is fixed firmly, that it stays clear as the gate swings, and that the bolt meets the strike every time the gate closes. Then test the credentials (on L2, the inside keypad too) and a battery change.
Specify L1 or L2 and the rear-body material and finish for each configuration, and list any remote control with its quantity. Test reports for the models they cover are listed on quality documents. Logo, finish and packaging for private-label orders are covered on OEM/ODM.
Frequently Asked Questions
Where does the lock body mount?
On the rear face of the gate, as a surface-mounted rim body. The gate needs firm fixing support, room for the 45 mm projection and a strike on the post.
Is L2 a separate lock?
No. L2 is a version of L1: its rear lock body has a built-in keypad for PIN operation from the inside. The front unit, gate fit and power are the same as L1.
How does the Tuya version's capacity work?
It holds 100 fingerprints plus up to 300 PINs and cards in total. The TTLock version holds 100 fingerprints, 250 PINs and 1,000 cards.
Is the rear body stainless steel?
It comes in stainless steel or iron. The front housing is SUS304 stainless steel in both.
Get an L1 Quote
Send photos of both sides of the gate, the gate thickness, the gap to the post, L1 or L2, the TTLock or Tuya version, the rear-body material and the quantity. We will confirm the fit and quote L1 for your gates. Qualifying material and manufacturing defects are covered for three years from shipment under our warranty policy.




