Glass Door Smart Lock

A7 Glass Door Smart Lock

The A7 glass door smart lock fits frameless glass doors 8–12 mm thick and framed glass doors, with optional clamps for other frame sizes. It comes in a fingerprint or a 3D face version, each with Tuya Bluetooth or TTLock, so you choose the mounting and the electronics separately.

A7 glass door smart lock, fingerprint version
8–12 mmFrameless glass
30–120 mmFramed doors
6 clampsOptional sizes
4 versionsFingerprint or face, Tuya or TTLock
IP55For indoor and covered doors
Specs

A7 Specifications

Format
Glass door lock, frameless or framed
Housing
SUS304 stainless steel and aluminum-alloy components
Finish
Stainless steel
Frameless glass
8–12 mm glass, 4–15 mm gap
Framed doors
30–120 mm across the framed versions; standard drilled version 30–90 mm
Front panel
192 × 78 mm; side profile 190 × 39 mm
Protection
IP55
Power
Fingerprint version 4 × AA; face version 4,000 mAh lithium
Emergency power
5 V Type-C
Mounting
Frameless clamp, framed drilled, or optional frame clamp
Access
Fingerprint, PIN, RFID card, mechanical key; 3D face on the face version
Working temperature
−25°C to 60°C
Options
Frame clamps; remote control
Details

Photos and Drawings

A7 smart lock fitted to a frameless glass office door

A7 smart lock fitted to a frameless glass office door

A7 front and inside units side by side
A7 dimension drawing with 192 × 78 mm front and 190 × 39 mm side profile
A7 glass clamp and receiving hardware
A7 face recognition version
Mounting

Mounting on Glass

Choose the mounting first, from the door's construction:

DoorHow A7 mountsRange
Frameless glassClamp on the glass edge8–12 mm glass, 4–15 mm gap
Framed door, standardDrilled through the frame30–90 mm
Framed door, optionalFrame clamp, sized to the frameSee the clamp table below

Across its framed versions, A7 covers doors 30–120 mm; the drawing confirms which mounting suits a given frame.

Optional clampFrame thickness
23 mm clamp15–20 mm
35 mm clamp28–32 mm
42 mm clamp34–39 mm
47 mm clamp40–44 mm
50 mm clamp45–47 mm
53.5 mm clamp48–50 mm

Any holes or cutouts in tempered glass must be made before tempering, so plan them with the glass fabricator. Existing finished glass is matched to its existing preparation, or fitted with the clamp mounting. The door should close to the same position every time on its hinges or pivots before the lock is approved. See our installation guide.

Versions

Fingerprint or Face, Tuya or TTLock

VersionFacesFingerprintsPINsCards
Fingerprint + Tuya Bluetooth—10050100
Fingerprint + TTLock—1002501,000
Face + Tuya Bluetooth10010050100
Face + TTLock1001002501,000

The face version suits offices and entrances where staff enter without touching the lock; test it at the installed height and from the normal approach. Remote access on the TTLock versions needs a TTLock gateway and a Wi-Fi connection. A remote control is available as an accessory. See app, gateway and access management.

Power

Power and Location

The fingerprint version runs on 4 replaceable AA batteries; the face version on a 4,000 mAh lithium battery, recharged as a pack. If the battery runs flat, a power bank on the 5 V Type-C port powers the lock temporarily, and the mechanical key is a second backup.

A7 is rated IP55 and works from −25°C to 60°C. We recommend it for indoor and covered glass doors.

Compare

Compare Indoor and Glass Door Models

Samples

Samples and OEM

Samples are available for evaluation; we confirm the version, door fit and accessories before an order. Order the A7 sample with the mounting and receiving set you plan to use. Fit it on representative glass or frame, and check that the hardware seats firmly and the door closes onto the receiver. Then test the chosen version, fingerprint or face.

Each entrance can then be quoted by its mounting group, with the version and clamp size on each line. Test reports for the models they cover are listed on quality documents. Logo, finish and packaging for private-label orders are covered on OEM/ODM.

FAQ

Frequently Asked Questions

Does the face version use AA batteries?

No. The fingerprint version uses 4 AA batteries; the face version uses a 4,000 mAh lithium battery.

What do the clamp sizes mean?

Each optional clamp fits a range of frame thicknesses, from 15–20 mm for the 23 mm clamp to 48–50 mm for the 53.5 mm clamp. Frameless 8–12 mm glass uses the standard glass clamp instead.

Can A7 be fitted to existing tempered glass?

Yes, by matching A7 to the glass's existing preparation or by using the clamp mounting. New holes or cutouts in tempered glass must be made before tempering.

What should a glass door inquiry include?

Photos of the whole entrance, the glass or frame thickness, the gap between the doors, the opening direction and any existing holes or fittings.

Get Started

Get an A7 Quote

Send photos of the entrance, the glass or frame thickness, the gap, the version (fingerprint or face, Tuya or TTLock) and the quantity. We will confirm the mounting and quote A7 for your doors. Qualifying material and manufacturing defects are covered for three years from shipment under our warranty policy.