Glass Door Smart Locks

Glass Door Smart Locks for Frameless and Framed Entrances

Our glass door smart lock, the A7, fits both frameless glass doors (8–12 mm glass) and framed glass doors with a 30–120 mm frame. It comes in four versions: fingerprint or 3D face, each with Tuya or TTLock. A7 is made in our Jinhua factory with SUS304 stainless steel and aluminum alloy parts.

  • 8–12 mm frameless glass, 4–15 mm gap
  • Framed doors 30–120 mm
  • Fingerprint or 3D face version
  • No-drill clamps for framed doors
A7 smart lock mounted on a frameless glass office entrance
Model

The A7 Glass Door Lock

A7 mounts on the glass or frame instead of in a mortise pocket, so it suits doors with no stile to cut into. The front unit measures 192 × 78 mm and is rated IP55 and works from −25°C to 60°C. We recommend it for indoor and sheltered entrances.

Fingerprint, PIN, RFID card and mechanical key come on every version; the face version adds 3D face recognition. The fingerprint versions run on four AA batteries, the face versions on a 4,000 mAh lithium battery, and all have a 5 V Type-C emergency input.

A7 glass door smart lock
Door Fit

Frameless or Framed Glass

Choose the mounting route first; each route is measured differently.

Mounting routeWhat you measureRange
Frameless glass, clampGlass thickness, and the gap to the fixed pane or wall8–12 mm glass; 4–15 mm gap
Framed door, drilled (standard)Frame thickness at the lock30–90 mm
Framed door, model rangeFrame thickness at the lock30–120 mm, by version and fitting
Framed door, optional no-drill clampFrame thickness, per clamp size below15–50 mm

The optional clamp comes in six sizes, and each fits only its own frame-thickness range, so measure the frame before choosing the no-drill route. The sizes are listed on the A7 glass door smart lock page.

Tempered glass cannot be drilled after tempering. If new glass needs holes or cutouts, put them in the glass supplier's drawing before tempering.

Versions

A7 Versions and Capacities

A7 comes in four versions: fingerprint or 3D face, each on Tuya Bluetooth or TTLock. The fingerprint versions run on 4 × AA batteries and the face versions on a 4,000 mAh lithium battery; the TTLock versions hold more PINs and cards. The A7 page lists the capacity of each version.

Choose TTLock when an office issues many cards, and Tuya when the users already run Tuya devices. Remote access on TTLock models needs a TTLock gateway and a Wi-Fi connection.

Strike

The Strike and the Closing Gap

The strike on the fixed pane or frame decides whether the door locks without a push. Check the gap at lock height with the door closed and watch how the floor spring or closer brings the door to rest. On double glass doors, decide which leaf carries the lock and how the other leaf is held. Order the strike and clamp with the lock so the installer receives one complete set.

FAQ

Frequently Asked Questions

Can A7 be fitted without drilling the glass?

Yes. On frameless doors A7 clamps to 8–12 mm glass, and framed doors can use the optional no-drill clamp in place of the drilled installation.

What is the difference between glass thickness and frame thickness?

Glass thickness (8–12 mm) applies to frameless doors. Frame thickness (30–120 mm) applies to framed doors, and the clamp sizes refer to the frame.

Fingerprint or face version?

Fingerprint is the simpler choice for staff entrances and runs on AA batteries. The face version suits users who want hands-free entry and uses a rechargeable lithium battery.

Is A7 made in your own factory?

Yes. A7 is part of our in-house range at the Jinhua factory. Electronic modules come from qualified suppliers.

Can a narrow aluminum-framed glass door use a profile lock instead?

Often, yes. If the frame stile has room for a mortise, compare A1 or A11 on the aluminum profile door page.

Get Started

Discuss Your Glass Entrance

Send photos of the whole entrance, the glass or frame thickness, the gap at the lock side and the opening direction. Tell us fingerprint or face, and Tuya or TTLock.